Difference between revisions of "Homer GUI"

From LIBISIS
Jump to navigation Jump to search
Line 33: Line 33:
  
 
[[image:fig7.jpg|left]]  
 
[[image:fig7.jpg|left]]  
 +
* a) fill in the white beam run numor, and optionally select a hard mask (if there is one for your instrument)
 +
* b) the background limits can also be changed, if you have selected to perform a flat background subtraction on the homer panel, then these are the limits which will be used
 +
<br clear="all" />
  
<br clear="all" />
+
* A completed '''Diag''' panel may look something like this...
  
 
[[image:fig5.jpg|left]]  
 
[[image:fig5.jpg|left]]  
  
 
<br clear="all" />
 
<br clear="all" />
 
  
 
* click on the '''Absolute''' button to bring up the Absolute Normalisation panel, absolute normalisation is '''not''' selected to be performed by default
 
* click on the '''Absolute''' button to bring up the Absolute Normalisation panel, absolute normalisation is '''not''' selected to be performed by default
Line 46: Line 48:
 
* a) Generally the Mono Van white beam numor will be the same as the sample white beam numor, but in special cases for pre PCICP MAPS experiments a diffferent wiring was used for these runs, in this case select the appropriate drop-down menu [[image:fig9.jpg]], and select a different map file.
 
* a) Generally the Mono Van white beam numor will be the same as the sample white beam numor, but in special cases for pre PCICP MAPS experiments a diffferent wiring was used for these runs, in this case select the appropriate drop-down menu [[image:fig9.jpg]], and select a different map file.
 
* b) fill in appropriate Sample Mass, Sample RMM and Ei, which will be calculated.
 
* b) fill in appropriate Sample Mass, Sample RMM and Ei, which will be calculated.
 +
* c) select the radiobutton to perform the normalistion
 
<br clear="all" />
 
<br clear="all" />
 +
 +
* A completed '''Diag''' panel may look something like this...
  
 
[[image:fig6.jpg|left]]  
 
[[image:fig6.jpg|left]]  
  
 
<br clear="all" />
 
<br clear="all" />

Revision as of 13:14, 7 February 2008

  • Homer will start from the matlab command line to bring up a GUI window
>> Homer_ver0
Fig1.jpg

select your instrument using the drop-down menu, this will create the instrument defaults which were defined in the Homer Gui setup

Fig2.jpg



  • click on the Homer button to bring up the homer panel


Fig3.jpg
  1. a) The default map file for the instrument will be filled in, but you can select another one or one you have created using the Map File Format, provided you have placed it in the map file directory.
  2. b) Fill in energy values for the SPE file output
  3. c) The Ei will be determined from the run unless the Fix Ei radiobutton is selected
  4. d) If you want to subtract a flat background from the data then unselect the No Back radiobutton


  • A completed Homer panel may look something like this...


Fig4.jpg



  • click on the Diag button to bring up the Diag panel
Fig7.jpg
  • a) fill in the white beam run numor, and optionally select a hard mask (if there is one for your instrument)
  • b) the background limits can also be changed, if you have selected to perform a flat background subtraction on the homer panel, then these are the limits which will be used


  • A completed Diag panel may look something like this...
Fig5.jpg


  • click on the Absolute button to bring up the Absolute Normalisation panel, absolute normalisation is not selected to be performed by default
Fig8.jpg
  • a) Generally the Mono Van white beam numor will be the same as the sample white beam numor, but in special cases for pre PCICP MAPS experiments a diffferent wiring was used for these runs, in this case select the appropriate drop-down menu Fig9.jpg, and select a different map file.
  • b) fill in appropriate Sample Mass, Sample RMM and Ei, which will be calculated.
  • c) select the radiobutton to perform the normalistion


  • A completed Diag panel may look something like this...
Fig6.jpg